IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not readyĬode: vboxsf: Successfully loaded version 4.3.12 (interface 0x00010004) vboxsf: Successfully loaded version 4.3.12 (interface 0x00010004) usb 1-1: Atheros AR9170 is registered as 'phy0' ieee80211 phy0: Selected rate control algorithm 'minstrel_ht' ath: EEPROM indicates we should expect a direct regpair map usb 1-1: firmware: direct-loading firmware carl9170-1.fw usbcore: registered new interface driver carl9170 intel8x0: measured clock 128532 rejected intel8x0_measure_ac97_clock: measured 56017 usecs (7200 samples) intel8x0: measured clock 122176 rejected intel8x0_measure_ac97_clock: measured 58931 usecs (7200 samples) intel8x0: measured clock 170208 rejected intel8x0_measure_ac97_clock: measured 58023 usecs (9876 samples) usb 1-1: reset high-speed USB device number 2 using ehci-pci intel_rapl: no valid rapl domains found in package 0 intel_rapl: domain uncore energy ctr 0:0 not working, skip cfg80211: (start_freq - end_freq bandwidth), (max_antenna_gain, max_eirp) cfg80211: World regulatory domain updated: input: ImExPS/2 Generic Explorer Mouse as /devices/platform/i8042/serio1/input/input6 cfg80211: Calling CRDA to update world regulatory domain intel_rapl: domain core energy ctr 0:0 not working, skip intel_rapl: domain package energy ctr 0:0 not working, skip ![]() parport_pc 00:03: reported by Plug and Play ACPI vboxguest: Successfully loaded version 4.3.12 (interface 0x00010004) piix4_smbus 0000:00:07.0: SMBus base address uninitialized - upgrade BIOS or use force_addr=0xaddr No driver support for vblank timestamp query. Supports vblank timestamp caching Rev 2 (). microcode: CPU1 update to revision 0x1b failed microcode: CPU0 update to revision 0x1b failed platform microcode: firmware: direct-loading firmware intel-ucode/06-3a-09 usbcore: registered new interface driver usbhid hidraw: raw HID events driver (C) Jiri Kosina usb 2-1: New USB device strings: Mfr=1, Product=3, SerialNumber=0 usb 2-1: New USB device found, idVendor=80ee, idProduct=0021 usb 2-1: new full-speed USB device number 2 using ohci-pci usb 1-1: New USB device strings: Mfr=16, Product=32, SerialNumber=48 usb 1-1: New USB device found, idVendor=1435, idProduct=0804 usb 1-1: new high-speed USB device number 2 using ehci-pci tsc: Refined TSC clocksource calibration: 2272.442 MHz TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 RX packets:7106 errors:0 dropped:7106 overruns:0 frame:0 TX packets:12 errors:0 dropped:0 overruns:0 carrier:0 RX packets:12 errors:0 dropped:0 overruns:0 frame:0 TX packets:29 errors:0 dropped:0 overruns:0 carrier:0 RX packets:3 errors:0 dropped:0 overruns:0 frame:0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 talks about using mac80211 drivers instead of ieee80211 drivers, but this isn't something I've had to change before so I'm not excited to dive into that task as I'm not very fluent in Linux.Įth0 Link encap:Ethernet HWaddr 08:00:27:d9:d3:ee These cards have worked for me in the past (maybe 6-12 months ago) in a stock configuration so I'm wondering if there isn't a "feature" in one of the newer dist-upgrades that needs to be turned on to get the cards in promiscuous mode? ![]() In other words, they are dropping frames not intended for them. The cards will go into monitor mode and can be used for packet injection, but they aren't running in promiscuous mode. I have two Proxim 8494 and one Ubiquiti SR71 usb adapters and I'm getting similar results with all three units. I'm running Kali 32-bit in Virtualbox updated Friday with the latest upgrades/dist-upgrades (have also tested in a booted OS).
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |